LogoSmartHome Docs
LogoSmartHome Docs
HomepageSmartHome Docs
User Manual
Washer Dryer
User ManualLaundry Care

Washer Dryer

User manual for the MF200D86WB-14EAS washer dryer — safety, installation, quick start, programmes, options, MSmartHome Wi-Fi control, cleaning and troubleshooting.

Before you begin

Please read the following safety information thoroughly and follow it strictly to minimize the risk of fire or explosion, electric shock and to prevent property damage, personal injury or loss of life. Failing to follow these instructions shall void any warranty. Model: MF200D86WB-14EAS.

1. Safety Instructions

The manual uses three signal words:

Signal wordMeaning
Warning!A potentially dangerous situation which may result in death or serious injuries unless it is avoided.
Caution!A potentially dangerous situation which may result in slight or minor injuries or damage to property and the environment.
Note!A potentially dangerous situation which may result in slight or minor injuries.

Warning — Electric shock hazard

  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  • If the machine is damaged, it must not be operated unless repaired by the manufacturer, its service agent or similarly qualified persons. Risk of electric shock!

Children and vulnerable persons

  • The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Children should be supervised that they do not play with the appliance.
  • Children 3 years and under shall be kept away from the appliance or continuously supervised.
  • Animals and children may climb into the machine. Check the machine before every operation.
  • Do not climb or sit on the appliance.

Installation location and surrounding

  • All washing and additional substances are to be kept in a safe place out of the reach of children.
  • Do not install the machine on a carpet floor. The obstruction of the openings by a carpet can damage the machine.
  • Keep the appliance clear from heating sources and direct sunlight to avoid plastic and rubber parts to corrode.
  • Do not use the appliance in humid environments or rooms containing explosive or caustic gas. In case of water leakage or water splashes let the appliance dry in the open air.
  • The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the washer dryer.
  • Do not operate the machine in rooms with a temperature of below 5°C. This can cause damages to parts of it. If it is unavoidable, make sure to drain the water completely from the appliance after every use (see "Cleaning the drain pump filter") to avoid damages caused by frost.
  • Never use flammable sprays or substances in the immediate proximity of the appliance.

2. Product Description

Labelled diagram of the washer dryer showing top cover, control panel, power supply cord, drum, service flap, drain hose, door, detergent dispenser and water supply hose
Main parts of the washer dryer

Note

The product picture is for illustration only, please refer to the real product as reference.

Accessories supplied: 4 × cover caps, 1 × supply hose (cold water), 1 × owner's manual, acoustic sponge (optional).

3. Installation

Installation area

Warning

  • Stability is important to prevent the product from wandering! Make sure the machine is standing leveled and stable.
  • Make sure that the product does not stand onto the power cord.
  • Make sure to maintain the minimum distances from the walls as shown in the manual (W ≥ 20 mm).
Side view of the washer dryer between two walls showing the minimum side clearance W of at least 20 mm
Maintain a minimum side clearance of W ≥ 20 mm

Before installing the machine, select a location with the following characteristics:

  1. Rigid, dry, and level surface
  2. Avoid direct sunlight
  3. Sufficient ventilation
  4. Room temperature is above 0°C
  5. Keep far away from heat sources such as coal or gas burning appliances.

Unpacking the washer dryer

Warning

  • Packaging material (e.g. films, Styrofoam) can be dangerous for children.
  • There is a risk of suffocation! Keep all packaging well away from children.

Remove the cardboard box and styrofoam packing.

Lift the washer dryer and remove the base packaging. Make sure the small triangle foam (a) is removed with the bottom packaging together. If not, lay the unit down on the side surface and remove it manually.

Remove the tape securing the power supply cord and drain hose.

Remove the inlet hose from the drum.

Remove transport bolts

Warning

You must remove the transport bolts from the backside before using the product.

Three close-up photos of removing a transport bolt: loosening it with a spanner, pulling out the bolt with its rubber part, and closing the hole with a cover cap
Loosen the bolts, remove them with the rubber parts, then fit the cover caps

Loosen the 4 transport bolts with a spanner.

Remove the bolts including the rubber parts and keep them for future use.

Close the holes using the cover caps.

Levelling the washing machine

Warning

The lock nuts on all four feet must be screwed tightly against the housing.

Four-step diagram showing how to level the machine: the machine on its feet, raising a foot, lowering a foot, and tightening the lock nut against the housing
Turn each foot to raise or lower it, then tighten the lock nut against the housing

To make sure that the leveling feet are adequately anchored in the machine, first screw all leveling feet completely into the machine (the leveling feet could have loosened during transport).

Then level the machine with a spirit level. To do this, loosen the lock nuts on the leveling feet and turn the leveling feet until the machine is level.

Hold the leveling feet and screw the lock nuts of the four leveling feet against the housing so that the lock nuts are tight against the machine housing and the leveling feet can no longer loosen.

Drain hose

Warning

  • Do not kink or protract the drain hose.
  • Position the drain hose properly, otherwise damage might result from water leakage.
  • It is not allowed to remove the buckle of the drain pipe.

There are two ways to place the end of the drain hose (keep the outlet at Max. 100 cm / Min. 60 cm):

  1. Put it into the water trough.
  2. Connect it to the branch drain pipe of the trough.
Two side-view diagrams of drain hose placement: hooked into a water trough, and connected to the branch drain pipe of a sink, both with the outlet at a height between 60 cm and 100 cm
Keep the drain-hose outlet between Min. 60 cm and Max. 100 cm

Connect the water supply hose

Warning

To prevent leakage or water damage, follow these instructions. Do not kink, crush or modify the water inlet hose.

Connect the water supply hose to the water inlet valve and to a water tap with cold water.

Two close-up photos showing how to attach the water supply hose: screwing the coupling onto the rear water inlet valve, and screwing the other end onto a cold-water tap
Connect the supply hose to the inlet valve and to a cold-water tap by hand

Note

Connect manually, do not use tools. Check if the connections are tight.

Acoustic sponge

Note

Please make sure to assemble the acoustic sponges, which can effectively reduce the noise caused by the machine while working, in order to provide you with a more peaceful and quiet living environment.

Get the machine laid on the floor, using some soft material like foam or clothes between the machine and floor for protection.

Stick the 2× longer sponges to the longer bottom edges of the machine, and the 2× shorter sponges to the shorter bottom edges.

4. Quick Start

Caution

  • Before washing, please make sure the washer dryer is installed properly.
  • Your appliance was thoroughly checked before it left the factory. To remove any residual water and to neutralize potential odors, it is recommended to clean your appliance before first use. For this reason, start the Cotton program at 90°C without laundry and detergent.

Calibration

It is recommended to calibrate the washing machine so that it provides the best performance. The appliance is able to detect the amount of laundry loaded. This function optimizes the product performance by minimizing energy and water consumption, saving you money and time.

Remove all accessories from the drum and close the door.

Insert the mains plug to the socket.

Switch on the washing machine, and within 10 seconds press Turbo and Airfresh simultaneously and continuously (normally 3 seconds) until "t19" is displayed on the knob.

Press Start/Pause to start the appliance. Initially "---" is displayed, and then "***" (such as "126") is displayed to indicate the real-time drum speed. When the number reaches a certain value (stops changing), it means the washing machine is successfully calibrated.

1. Before washing

Plug in — connect the mains plug (earth terminal).

Open tap — open the water tap.

Load — place the laundry in the drum.

Close door — close the door.

Add detergent — fill the dispenser compartments (Main wash, Softener, Prewash).

Five-step strip before washing: plug in to the earthed socket, open the water tap, load the laundry into the drum, close the door, and add detergent to the Main wash, Softener and Prewash compartments
Before washing: plug in, open tap, load, close door, add detergent

Note

Detergent needs to be added in compartment I if the pre-wash function is selected.

2. Washing

Power on the machine.

Select programme with the knob.

Select function or keep the default settings.

Press Start/Pause to start the program.

3. After washing

The buzzer beeps and "End" appears on the display.

Before each washing

  • The ambient temperature of the washer dryer should be 5–40°C. If used under 0°C, the inlet valve and draining system may be damaged. If the machine is installed under freezing conditions, it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose can unfreeze before use.
  • Please check your laundry care labels and the detergent use instructions before washing. Use non-foaming or less-foaming detergent suitable for machine washing properly.

Check the care label.

Sort laundry according to color and textile type.

Take all items out of the pockets.

Tie together long textile strips and belts, close zips and buttons.

Put small items into a laundry bag.

Turn easy-pilling and long-pile fabric inside out.

Warning

  • Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances like wax, oil, paint, gasoline, alcohol, kerosene, and other flammable materials.
  • Washing single clothes items may easily create big eccentricity. Therefore it is suggested to add one or two more laundry items to the wash so that the spin can be done smoothly.

5. Detergent Dispenser

Detergent dispenser drawer with compartment I for pre-wash, compartment II for main wash, and a softener compartment
I — Pre wash · II — Main wash · ✿ — Softener

The dispenser drawer has three compartments. Press the release button to pull out the dispenser.

SymbolCompartment
IPre wash
IIMain wash
✿Softener

Caution

Detergent only needs to be added in "compartment I" after selecting the pre-wash function.

Which compartment each programme uses

(● means must · ○ means optional)

ProgrammeI (Pre wash)II (Main wash)✿ (Softener)
Cotton○●○
Mix○●○
Wash and Dry—●○
Auto Dry———
Time Dry———
Allergy Care○●○
Steam Care○●○
1h WD—●○
Quick 15'—●○
20℃—●○
ECO 40-60—●○
Wool—●○
Bulky○●○
Rinse & Spin——○
Spin Only———
Drum Clean———

Detergent recommendation

Recommended detergentWash cyclesWashing temp.Type of laundry and textile
Heavy-duty detergent with bleaching agents and optical brightenersCotton, ECO 40-60, Mix, Bulky20/30/40/60White laundry made from boil-proof cotton or linen
Colour detergent without bleaching agent and optical brightenersCotton, ECO 40-60, Mix, Bulky, 20℃Cold/20/30/40Coloured laundry made from cotton or linen
Colour or mild detergent without optical brighteners20℃Cold/20Coloured laundry made from easy-care fibres or synthetic materials
Mild washing detergentWool20/30Delicate textiles, silk, viscose
Special wool detergentWool20/30Wool

Note — detergent dosing

  • Agglomerating or ropy detergent or additive can be diluted in some water before pouring it into the detergent dispenser, to avoid its inlet getting blocked and causing a water overflow.
  • Choose the suitable type of detergent for maximum washing performance and minimum water and energy consumption.
  • To achieve the best cleaning result, proper detergent dosing is important.
  • Use a reduced detergent amount if the drum is not filled completely.
  • Always adjust the amount of detergent to the water hardness; if your tap water is soft, use less detergent.
  • Dose according to how dirty your laundry is; less dirty clothes require less detergent.
  • Highly concentrated (compact) detergent requires particularly accurate dosing.

Signs of detergent overdosing: heavy foam formation; poor washing and rinsing result.

Signs of detergent underdosing: laundry turns grey; build-up of limescale deposits on the drum, the heating element and/or the laundry.

6. Control Panel

Control panel with the programme list on the left, the option buttons in the centre and the On/Off and Start/Pause buttons on the right, with numbered callouts
Control panel overview
#ControlFunction
1On/OffPower on or off the machine.
2Start/PauseStart or pause your program.
3OptionPress the buttons to change program parameters or select additional functions.
4ProgramChoose the appropriate program according to the laundry type.
5DisplayShows settings, estimated remaining time, options and status messages.

Display indicators

Display legend showing the meaning of each icon: Wi-Fi, Remote Control, Delay, Door Lock, Child Lock, SteamCare, AutoClean, Pre Wash, Wash, Rinse, Spin, Dry, Time Dry, Airfresh and the digital readout
Meaning of the display icons
IconMeaningIconMeaning
ADisplay (Wash Time, Speed, End / Delay Time, Error, Temp.)BRemote Control
CDelayDDoor Lock
EChild LockFSteamCare
GAutoCleanHPre Wash
IWashJRinse
KSpinLDry
MDryNTime Dry
OAirfreshPWiFi

7. Programmes

Programmes are available according to the laundry type.

ProgrammeWash / Dry load (kg)Display time
Cotton8.0 / 6.03:49
Mix8.0 / 6.01:30
Wash and Dry6.0 / 6.05:04
Auto Dry— / 6.04:14
Time Dry— / 0.50:40
Allergy Care4.02:38
Steam Care4.01:57
Quick 15'2.00:15
20℃4.01:01
ECO 40-608.03:38
Wool2.01:07
Bulky8.01:48
Rinse & Spin8.00:20
Spin Only8.00:12
Drum Clean—1:18
1h WD1.0 / 1.00:59

Note

The parameters in this table are for reference only. The actual parameters may differ. The values given for programmes other than the ECO 40-60 programme and the Wash and Dry cycle are indicative only. The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration. Loading the washer-dryer up to the capacity indicated for the respective programme will contribute to energy and water savings.

Programme descriptions

ProgrammeDescription
CottonHard-wearing textiles, heat-resistant textiles made of cotton or linen.
MixMixed load consisting of textiles made of cotton and synthetics.
Auto DryDesigned for drying clothes automatically to achieve the best dry performance.
Time DryDrying for a set time.
Wash and DryContinuous washing and drying program.
20℃Washing brightly coloured clothes; protects the colours better.
Allergy CareApplies 60℃ high-temperature sterilization to make the wash more clean and achieve the anti-allergy effect.
Steam CareFor daily laundry like cotton and synthetics. Steam penetrates the fibre deeply, effectively eliminating bacteria and germs, preventing odors.
Quick 15'Extra-short program, suitable for lightly soiled, small amounts of laundry.
1h WDFor small synthetic clothes or shirts; load limit 1 kg (about 4 shirts).
ECO 40-60Default 40℃ (not selectable), suitable for laundry washing at about 40–60℃.
BulkySpecially designed for washing duvet coats.
WoolHand- or machine-washable wool or rich-wool textiles. Especially gentle wash program to prevent shrinkage, with longer program pauses (textiles rest in the wash liquor).
Rinse & SpinExtra rinse with spin.
Spin OnlyExtra spin with selectable spin speed.
Drum CleanCleans the drum and tube; applies 90°C high-temperature sterilization. No clothes or other washing can be added. Adding a proper amount of chlorine bleaching agent improves the cleaning effect. Use regularly according to need.

Caution

If there is any break in the power supply while the machine is operating, a special memory stores the selected programme. The machine will continue the programme when the power supply is re-established.

8. Options

The default spin speed and the adjustable options depend on the selected programme.

ProgrammeTemp. (℃)Default spin (rpm)
Cotton401200
Mix40800
Wash and Dry—1400
Auto Dry—1400
Time Dry—1400
Allergy Care60800
Steam Care40800
Quick 15'Cold800
20℃201000
ECO 40-60—1400
Wool40600
Bulky401000
Rinse & Spin—1000
Spin Only—1000
1h WD——
Drum Clean——

Note

For the maximum spin speed, program time and other details of the ECO 40-60 and Wash and Dry programs, please refer to the Product Fiche section. The table shows which cycle offers which options for adjustment.

Spin

When needed, the spinning speed can be adjusted by pressing the Speed button in the following steps: 0 – 400 – 600 – 800 – 1000 – 1200 – 1400.

Temp.

When needed, the washing temperature can be adjusted by pressing the Temperature button in the following steps: Cold – 20°C – 30°C – 40°C – 60°C – 90°C. You can also turn off the Wi-Fi function by pressing this button for 3 seconds (see the MSmartHome section).

Pre Wash

Extra washing function before the main washing cycle starts, to increase the washing performance.

Note

Detergent needs to be added to the detergent dispenser compartment I.

Turbo

The function can decrease the washing time.

Wi-Fi / Remote Control

Turn on the Wi-Fi function and configure/reset the network or control remotely by pressing the button for 3 seconds (see the MSmartHome section).

AutoClean

The AutoClean function is automatically activated during every washing cycle to keep your laundry always clean. AutoClean is used to clean the drum as a default function and is only applicable to the following programs — Rinse & Spin, Steam Care, Allergy Care, Jeans, Mix and Cotton. It happens between the first and second rinse: a small amount of water is fed and the drum is rinsed. This function continues for about 10 minutes.

SteamCare

SteamCare is a function added before the main wash that generates warm steam for sterilization and greater washing performance.

Caution

Some programs have automatically added AutoClean or SteamCare functions. These two functions can't be manually selected or canceled.

Dry

Press the Dry button continuously to choose the dry level: Gentle Dry (Soft) / Normal Dry (Normal) / Extra Dry, and Time Dry.

LevelMeaning
d-1 Gentle Dry (Soft)Clothes are dried to a damp state for ironing.
d-2 Normal Dry (Normal)Clothes are ready for storing in the cupboard.
d-3 Extra DryClothes are dried completely to be worn directly.
Timed DryDry your laundry and finish within a given time (30 / 60 / 90 / 120 / 180 minutes).

Note — drying hints

  • Thoroughly spin your laundry before drying.
  • To ensure proper drying, sort your laundry according to fabric type and drying temperature.

Clothes not suitable for drying

  • Particularly delicate items such as synthetic curtains, woollen and silk items, clothes with metal inserts, nylon stockings, and bulky clothes such as anoraks, bedcovers, quilts, sleeping bags and duvets must not be dried.
  • Clothes padded with foam-rubber or similar materials must not be machine dried.
  • Fabrics containing residues of setting lotions, hair sprays, nail solvents or similar solutions must not be machine dried, to avoid the formation of harmful vapours.

Mute the buzzer

Press the Extra Rinse button for 3 seconds to mute the buzzer. To re-activate the buzzer, press the button again for 3 seconds. The setting is kept until the next reset.

Airfresh

The drum repeats rotating for half an hour and stopping for another half hour, shaking up the clothes to avoid laundry being left in the washer dryer; the total time increases by 8 hours. The fan also circulates air through the washer dryer to prevent odors and keep clothes fresh.

9. MSmartHome (Wi-Fi Control)

Before you start, make sure that:

  1. Your smartphone is connected to the home Wi-Fi network and you know the network password.
  2. You are near the home appliance.
  3. The 2.4 GHz band wireless signal is enabled on your wireless router.
QR code to download the MSmartHome app, with the App Store and Google Play badges
Download the MSmartHome app & activate your product

Follow these steps to enter the remote control state

Download the MSmartHome app. Scan the QR code above, or search for "MSmartHome" in Google Play (Android) or the App Store (iOS) to download the app.

Register or log in. Open the app and create a user account; if you already have one, just log in. Select your country correctly in the country list (the countries are listed in the order of the first letter).

Add your appliance. Tap the "+" (Add device) icon to add the home appliance to your MSmartHome account. Select the correct appliance type "Washing Machine", then select the model type "MF200" according to your appliance.

Connect to the network. Make sure your smartphone is connected to the home Wi-Fi network so you can enter your home Wi-Fi password. Rotate the knob randomly to indicate one of the programs, and press the Wi-Fi button continuously until "AP" shows in the knob display. Then connect your mobile phone to the Wi-Fi signal sent out by the appliance (default password "12345678"). Finally, return to MSmartHome to start the connection. Network configuration is now complete.

Start remote control. Rotate the knob randomly to indicate one of the programs, and press the Wi-Fi button continuously until the remote control icon lights up in the knob display. This means it has entered the remote control state and you can start to control it remotely.

Wi-Fi status light

Status lightMeaning
Slowly flashingWaiting for connection
Quickly flashingConnecting
Quickly flashing solidConnected to your wireless router

Notes on networking

  • When networking the product, make sure that the mobile phone is as close as possible to the product.
  • If the product only supports 2.4 GHz Wi-Fi communication, make sure the 2.4 GHz network is selected for connection.
  • Midea recommends Wi-Fi router SSID names contain only alphanumeric values. If special characters, punctuation marks or spaces are used, the SSID name might not show up in the available networks to join in the app. If the SSID shows up then it is OK to use; otherwise log into the router and change the SSID name.
  • A large number of devices on the Wi-Fi router can affect network stability.
  • If the router or Wi-Fi name and password change, repeat the above process to reconnect to the network.
  • As the product technology is updated, the content of MSmartHome may change, and the actual display in the MSmartHome app shall prevail.

Turn the Wi-Fi function on / off / reset

ActionProcedure
Turn off Wi-FiPress Temp. for 3 seconds.
Turn on Wi-FiPress the Wi-Fi button for 3 seconds.
Reset Wi-Fi configurationPress the Wi-Fi button for 3 seconds to turn on Wi-Fi and re-enter network configuration. "AP" appears on the knob display. Reconnect to the network as above.

10. Cleaning and Care

Warning

Always unplug the appliance and close the water tap before cleaning and maintenance.

Cleaning the cabinet

Proper maintenance can extend the working life of the washing machine. The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use a towel to wipe it off immediately. Never use sharp items to clean the appliance.

Caution

Never use abrasive or caustic agents, formic acids or their diluted solvents or similar substances, like alcohol or chemical products.

Cleaning the drum

Any rust stains left inside the drum by metal articles must be removed immediately using chlorine-free detergents. Never use steel wool for cleaning the drum!

Note

Keep any laundry away from the machine while cleaning the drum.

Cleaning the door seal and glass

Wipe the glass and seal after each wash to remove lint and stains. If lint builds up it can cause leakages. Remove any coins, buttons and other objects from the seal after each wash. Clean the door seal and glass every month to ensure the normal operation of the appliance.

Cleaning the inlet filter

Note

Diminishing water flow is a sign that the filter needs to be cleaned.

Four-step diagram for cleaning the inlet filter: unscrew the supply hose from the tap, brush the tap-end filter, unscrew the hose from the back of the machine and pull out the inlet filter, then brush that filter clean
Clean the filters at both the tap end and the machine inlet

Close the tap and remove the water supply hose from it.

Clean the filter with a brush.

Unscrew the water supply hose from the backside of the machine. Pull out the filter with long-nose pliers.

Use a brush to clean the filter.

Reinstall the filter to the water inlet and reconnect the water supply hose.

Clean the inlet filter every 3 months to ensure the normal operation of the appliance.

Cleaning the detergent dispenser

Four-step diagram for cleaning the detergent dispenser: press the release and pull out the drawer, rinse the drawer and softener cover under water, brush the inside of the recess, and slide the drawer back in
Remove, rinse and brush the dispenser drawer and recess

Press down the release on the softener cover and pull the dispenser drawer out of the recess.

Lift the softener cover off the dispenser drawer and wash both items with water.

Clean the inside of the recess with a soft brush.

Restore the softener cover and push the drawer back into the recess.

Note

  • Do not use abrasive or caustic agents to clean plastic parts.
  • Clean the detergent dispenser every 3 months to ensure the normal operation of the appliance.

Cleaning the drain pump filter

Warning

  • Make sure that the machine has finished the washing cycle and is empty. Switch it off and unplug it before cleaning the drain pump filter.
  • Be careful of hot water. Wait for the water to cool down. Risk of scalding!
  • Clean the filter periodically every 3 months to ensure the normal operation of the appliance.
Six-step diagram for cleaning the drain pump filter: open the lower cover cap, pull out the emergency drain hose and remove its cap, let the water drain then reset the hose, unscrew the filter counter-clockwise, remove debris from the filter, and close the lower cover cap
Drain the residual water, then unscrew and clean the drain pump filter

Open the lower cover cap.

Pull out the emergency drain hose and take off the hose cap.

After the water runs out, reset the drain hose.

Open the filter by turning it counter-clockwise.

Remove extraneous matter.

Close the lower cover cap.

Caution

Make sure the emergency drain hose cap and the emergency drain hose are reinstalled properly, otherwise water may leak.

Emergency door release

In case of a power failure or other circumstances where the door cannot be opened, if it is necessary to open the door, pull down the pull cord inside the emergency door and restore the pull cord after opening the door.

Three-step diagram for the emergency door release: open the filter door to reveal the emergency door pull cord, insert a straight screwdriver into the pull cord, and pull the cord down in the direction of the arrow to unlock the door
Open the filter door and pull the emergency cord down to unlock the door

Open the filter door.

Using a straight screwdriver (or other non-sharp tool), insert it into the emergency door pull cord.

Pull down the emergency door pull cord (in the direction of the arrow). If unlocked successfully, the door lock icon will go out.

Warning

The machine is not allowed to use the emergency switch pull cord during washing. If you need to run the machine urgently, it is recommended to open the door after the water has cooled, to avoid burns caused by high-temperature residual water flowing out of the machine tub.

11. Troubleshooting

Whenever there is a problem with the appliance, check if you can solve it following the tables below. If the problem persists, please contact customer service.

DescriptionPossible causeSolution
Appliance does not startDoor is not closed properly. Clothes are stuck.Close the door properly and restart. Check the laundry.
Door can't be openedSafety protection is activated.Disconnect the power and restart.
Water leakageConnections are not tight enough.Check and fasten the water inlet pipe. Check and clean the outlet hose.
Detergent residues in the dispenserDetergent is damp and/or clotted.Clean and wipe the detergent dispenser dry.
Indicator or display does not workPC board or harness have connection problems.Switch off the power and check if the mains plug is connected properly.
Abnormal noiseFixing bolts still in place. Floor is not solid or level.Check if the fixing bolts have been removed. Make sure the appliance is installed on a solid and level floor.

Error codes

Possible causeSolution
Door is not closed properlyClose the door properly and restart.
Water injecting problem during wash cycleCheck if the water pressure is high enough. Straighten the water pipe. Clean the inlet valve filter.
Overtime water drainingCheck the drain hose for blockage.
Water overflowRestart the appliance.
OthersRestart the appliance. If the problem persists, please contact customer service.

Risk of electric shock

  • Never try to repair an appliance which is defective or presumed to be defective. You may put your own and future users' lives in danger. Only authorised specialists are allowed to carry out repair work.
  • Improper repair will void the warranty and subsequent damages can't be recognized.

Customer service

Key spare parts for your appliance are available for a minimum of 10 years following EU Commission Regulation 2019/2023 Annex II Ecodesign requirements. Delivery of spare parts within 15 working days after having received the order.

Transport — important steps when moving the appliance

  • Unplug the appliance and close the water inlet tap.
  • Check if the door and the detergent dispenser are closed properly.
  • Remove the water inlet pipe and the outlet hose from the house installations.
  • Let the water drain completely from the appliance (see "Cleaning the drain pump filter").
  • Important: re-install the 4 transport bolts in the back of the appliance.
  • This appliance is heavy. Transport with care. Never hold any protruding part of the machine when lifting. The machine door cannot be used as a handle.

12. Technical Specifications

ItemValue
ModelMF200D86WB-14EAS
Power supply220–240 V~, 50 Hz
Max. current10 A
Standard water pressure0.05 MPa ~ 1 MPa
Washing capacity8.0 kg
Drying capacity6.0 kg
Dimensions (W × D × H)595 × 475 × 850 mm
Weight65 kg
Rated power1900 W
Drying power1300 W

Product Fiche

The actual energy and water consumption will depend on how the appliance is used and on the hardness of the water.

PortaSplit (Two-Part Air Conditioner)

Install, operate and maintain the Midea PortaSplit split air conditioner (model MMCS-12HRN8-QRDO) — from bracket mounting and modes to remote control and the SmartHome app.

Dishwasher

Set up, connect over Wi-Fi, and operate your Comfee countertop dishwasher — wash programs, salt and detergent, maintenance, installation and troubleshooting.

Table of Contents

1. Safety Instructions
Children and vulnerable persons
Installation location and surrounding
2. Product Description
3. Installation
Installation area
Unpacking the washer dryer
Remove transport bolts
Levelling the washing machine
Drain hose
Connect the water supply hose
Acoustic sponge
4. Quick Start
Calibration
1. Before washing
2. Washing
3. After washing
Before each washing
5. Detergent Dispenser
Which compartment each programme uses
Detergent recommendation
6. Control Panel
Display indicators
7. Programmes
Programme descriptions
8. Options
Spin
Temp.
Pre Wash
Turbo
Wi-Fi / Remote Control
AutoClean
SteamCare
Dry
Mute the buzzer
Airfresh
9. MSmartHome (Wi-Fi Control)
Follow these steps to enter the remote control state
Wi-Fi status light
Turn the Wi-Fi function on / off / reset
10. Cleaning and Care
Cleaning the cabinet
Cleaning the drum
Cleaning the door seal and glass
Cleaning the inlet filter
Cleaning the detergent dispenser
Cleaning the drain pump filter
Emergency door release
11. Troubleshooting
Error codes
Transport — important steps when moving the appliance
12. Technical Specifications
Product Fiche